up level       

 LEDNEON - FLEX
      Though neon has long been the mainstream of the outdoors linear lighting, it is also known for its technical weaknesses, including complicated installation, fragile glass nature, potential shock hazard, high maintenance cost and high power consumption. However, the market for outdoor linear lighting is so vast that many manufactures try to find a perfect substitute for neon, but they all fail to solve the above problems. With over 2 years' advanced LED technologicalresearch and development work, Neo-Neon has finally succeededin producing LEDNEON-FLEX to replace glass neon. Compared with glass neon, it is easier to cut and can be bent into whatever angles by hand, installation can be within minutes and most important,
it gives no hot spot on appearance.

• LEDNEON FLEX SPECIFICATION :

ITEM NO. LENGTH IN ROLL DIMENSION LED SPACING TOTAL NO. OF LED TOTAL WATTS
LN-FX-10-240V
9.1m
14X27.5MM
0.5"
720
43.2W
10.0m
792
66W
LN-FX-50-240V
48.8m
14X27.5MM
0.5"
3840
230.4W
49.4m
3888
324W
LN-FX-30-120V
30FT
14X27.5MM
0.5"
720
43.2W
720
60W
LN-FX-150-120V
150FT
14X27.5MM
0.5"
3600
216W
3600
300W
LN-FX-30-24V
30FT
14X27.5MM
0.5"
720
64.8W
720
72W
ITEM NO.
NO.OF LED PER UNIT
CUTTING UNIT
WATTS PER METER OR FOOT
LED COLOR
MAX. LOADING LENGTH
LN-FX-10-240V
120
1.52M
4.7W/M
R,Y,O
58M (With 1.6A converter)
146M (With 4A converter)
72
0.91M
6.6W/M
G,B,W
LN-FX-50-240V
120
1.52M
4.7W/M
R,Y,O
72
0.91M
6.6W/M
G,B,W
LN-FX-30-120V
60
2.5FT
1.44W/FT
R,Y,O
96FT (With 1.6A onverter)
240FT (With 4A onverter)
36
1.5FT
2W/FT
G,B.W
LN-FX-150-120V
60
2.5FT
1.44W/FT
R,Y,O
36
1.5FT
2W/FT
G,B,W
LN-FX-30-24V
8
1/3FT
2.16W/FT
R,Y,O
16FT (With 1.6A onverter)
40FT (With 4A converter)
6
1/4FT
2.4W/FT
G,B,W

Recommended storage & operating temperature: -20°C to 60°C, 100% humidity.
• Installing Mode :
     The LEDNEON-FLEX is a versatile and user-friendly lighting device. It can be cut, bent and easily installed on the flat surface of various materials, such as wood, plastic, steel, or wall, etc. to form all kinds of pattern according to your design. And it can be easily connected to the power supply and then perform well.
  1. It is recommended to mark centerlines or draw the outline of your pattern on the surface of your desired positions.
  2. Secure mounting clips along the centerlines at appropriate intervals with screws. If there are curves, it is better to secure a mounting clip on and between each curve.
  3. Insert the light body into the mounting clips with the lighting parts upward.
  4. Connect each part together.

Straight line

Right Angle
Curve
1. Cut only at the cutting mark.
2. Connect the transformer and LEDCHANNEL-Flex together with connector.
3. Connect two parts with terminal block .
4. Extension cord is available for any length.
5. Terminate with end cap.

 

Copyrights 2006 by NeoNeon.co.th., All Rights Reserved Designed by Siammetal Services